If you’re looking to buy a new 100k thermistor table and still confused about which one is best.

Then you’re in the right place because Our team has spent more than 50 hours researching, comparing, and testing the different options available in the market nowadays to be able to compile the following list of picks for the best 100k thermistor table you can purchase right away from Amazon.

First, here are our picks for today along with our research score for each item.

Top 10 best 100k thermistor table (Our Favorites)

Now, let’s take a look at each item of the best 100k thermistor table, in order to know the different features & benefits of each pick.

FYSETC 3Pcs Upgrade HT-NTC100K Thermistor 3D Printer Parts Thermistor Sensor High Temperature +300 Degrees for CR10 Ender A8 Maker Pro Hot End Heater Block

$12.88  in stock
Amazon.com
as of May 6, 2022 8:56 pm

Features

  • Upgrade HT-NTC100K Thermistor: package temperature measurement. Temperature measurement head cylinder diameter 3mm, length 15mm, The connector is 2pin XH2.54, so make sure your heater block is the right hole, the board Connection terminal is the right type, can be used with the heating block that support the thermocouple.
  • The temperature measurement: -50 °C ~ +350 °C, can replace the original K-type thermocouple temperature, very fit for printing high-temperature filament.
  • Adopts 304 stainless steel, with the internal temperature package to ensure the maximum service life with precision temperature measurement.
  • HT-NTC100K thermistor adopts white high-temperature cord, can bear higher temperature. And for customers' convenience, the wires adopts line connection, the customer can tear the wires depends on their application. The high temperature line is double thicker than others in the market, not easy to break off.
  • Not fit for CR-6 SE heater block. After sales-guarantee: Need more help please email us, we will give you help within 24 hours.

Creality 3D Printer NTC Thermistor Temp Sensor 100K for Creality Ender 3 / Ender 3 Pro/Ender 5 / CR-10 / CR-10S (1m/39.4inch)

$9.66  in stock
2 new from $9.66
Free shipping
Amazon.com
as of May 6, 2022 8:56 pm

Features

  • Use for heated bed or extruder
  • It has 2 pins female connector
  • Wire length: 1m/39.4 inches
  • Package include: 5 thermistors
  • Temperature sensor 100KΩ accuracy of ± 1%

WINSINN HT-NTC100K Thermistor Sensor, Ender 3 v2 Upgrade 3x15 3950 XH2.54 2Pin, Compatible with Ender 3 5 Pro CR6 CR10 Series 3D Printer Hotend (Pack of 5Pcs)

$11.99
$9.48
 in stock
Amazon.com
as of May 6, 2022 8:56 pm

Features

  • ✔️Upgrade HT-NTC100K Thermistor: package temperature measurement. Head diameter: 3mm, Head length: 15mm
  • ✔️The temperature measurement: -50 °C ~ +350 °C, can replace the original K-type thermocouple temperature. Fit for printing high-temperature filament.
  • ✔️Adopts 304 stainless steel, with the internal temperature package to ensure the maximum service life with precision temperature measurement.
  • ✔️HT-NTC100K thermistor adopts white high-temperature cord, can bear higher temperature. And for customers' convenience, the wires adopts line connection, the customer can tear the wires depends on their application. The high temperature line is double thicker than others in the market, not easy to break off.
  • ✔️Made by WINSINN. Can be used with the New Sensor Heater Block (Temperature measurement can be up to 350 degrees).

Inkbird ITC-308 Digital Temperature Controller 2-Stage Outlet Thermostat Heating and Cooling Mode Carboy Homebrew Fermenter Greenhouse Terrarium 110V 10A 1100W

$35.00  in stock
2 new from $35.00
Free shipping
Amazon.com
as of May 6, 2022 8:56 pm

Features

  • 【Easy to use】 Supports °C/°F display.
  • 【Dual relay】able to power refrigeration and heating equipment as conditions change.
  • 【Dual Display Window】Displays measured temperature and set temperature at the same time.
  • 【Buzzer Alarm】High and low temperature alarms are available when the temperature is over or the sensor experiences a malfunction.
  • 【Safety】Maximum output load: 1100W(110V). Customize temperature and compressor delay, protecting your refrigeration/heating equipment.

10K Temperature Sensor Probe, DROK 5pcs 1 Meter Waterproof Temp Sensor Probe, Stainless Steel 3950 NTC Temp Sensor Probe, Digital Temperature Transmitter Extension Cable

$9.99  in stock
Amazon.com
as of May 6, 2022 8:56 pm

Features

  • Advanced Technology: DROK smart sensors cable adopts sensitive and reliable NTC thermistor and connected by PVC wire, 1 meter lead length (3.28ft), available for remote temperate measuring and controlling.
  • Wide Measuring Range: Our temperature probe is able to tolerate the widest measuring range (-25°c to 125°c (-13℉ to 257℉)).
  • Stainless Steel Probe: This temperature sensor for car has 5*25mm stainless steel housing, which is waterproof, moisture-proof and anti-rust.
  • Wide Application: This multifunctional test probes can be used in household air conditioner, refrigerator, water fountain, drying box, constant box, etc.

Upgrade M3 Hex Screw in Fixing Thermistor 100K 3950 Temperature Sensor for Ender 3 V2 Pro CR10 and Other 3D Printer Extruder Hotend (100K 3950)

$7.99  in stock
Amazon.com
as of May 6, 2022 8:56 pm

Features

  • M3 screw for installation is Quik and Durable, Flexible and Long Lasting, longer life span
  • DIY players can also modify BLOCK by themselves. Make an M3 threaded hole in BLCOK, then you can use this thermistor
  • Package: 1piece m3 screw in thermistor
  • Thermistor model: NTC 100K 3950. HERE is the firmware setting: *13:100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " &"Hotend "All In ONE" #define TEMP_SENSOR_0 13
  • For the printer which uses NTC 100K 3950 thermistor, Then this thermistor is plug and use

Genuine E3D Hotend Thermistor Cartridge Replacement

$11.91
$10.21
 in stock
9 new from $10.21
Free shipping
Amazon.com
as of May 6, 2022 8:56 pm

Features

  • Direct replacement of cartridge type thermistor in E3D hotends.
  • A custom made thermistor encapsulated into an easy to use cartridge package.
  • Genuine Semitec 104GT thermistors used.
  • Comes with (1) Hotend Thermistor with attached connector and (1) connector cable measuring 40 inches (101cm)

HICTOP 100K ohm NTC 3950 100k thermistor 1.2m/Temp Sensor for Reprap Creality Ender 3, Ender 3 Pro, CR-10 10S 3D Printer 2Pin XH2.54 (Pack of 5)

$10.99  in stock
Amazon.com
as of May 6, 2022 8:56 pm

Features

  • HICTOP 3d printer 100k thermistor 1.2m can be used on both of the heated bed and the extruder for 3d printers
  • The thermisor is compatible with most 3D printers in the market such as ender3, ender3 pro, ender3 V2, CR-10, hictop d3 hero etc
  • There is a 2 pin female connector on the thermistor for 3D printer
  • Wire length for the thermistor: 1.2m/47.2 inches.
  • Recommended parameters for the thermistor: R25℃=100K B25/50=3950K± 1%

FYSETC Prus i3 MK3 Upgrade Hotend Parts HT-NTC100K Thermistor Sensor High Temperature +300 Degrees 2 Pins for 3D Printer MK3 Extruder Heater Block 3Pcs

$14.99  in stock
Amazon.com
as of May 6, 2022 8:56 pm

Features

  • Upgrade HT-NTC100K Thermistor: package temperature measurement. Temperature measurement head cylinder diameter 3mm, length 15mm, can be used with the heating block that support the thermocouple.
  • The temperature measurement: -50 °C ~ +300 °C, can replace the original K-type thermocouple temperature, very fit for printing high-temperature filament. (Please note that the temperature should not be over 300 °C, otherwise the temperature will not be accurate.)
  • Adopts 304 stainless steel, with the internal temperature package to ensure the maximum service life with precision temperature measurement.
  • HT-NTC100K thermistor adopts white high-temperature cord, can bear higher temperature. And for customers' convenience, the wires adopts line connection, the customer can tear the wires depends on their application. The high temperature line is double thicker than others in the market, not easy to break off.
  • After sales-guarantee: Need more help please email us, we will give you help within 24 hours.

24V 50W Upgraded Ceramic Cartridge Heater 100K ohm NTC Thermistors 3D Printer Eewolf

$15.99  in stock
Amazon.com
as of May 6, 2022 8:56 pm

Features

  • Please make sure your heater block can hold the thermistor before purchasing as the thermistor head is bigger than normal one.
  • From the original ordinary 0.3-line high-temperature line to 0.5-line thick white high-temperature line, the 50w heater can bear higher temperature up to 340-350 ℃.
  • Upgrade HT-NTC100K Thermistor: head cylinder diameter 3mm, length 15mm, can be used with the heating block that support the thermocouple.
  • Working temperature: -50°C ~ +350°C, it can replace the original K-type thermistor, very fit for printing high-temperature filament.
  • 3pcs 24V 50W upgraded heater and 3pcs HT-NTC100K temp sensor. (heater not work on cr10 cr10s 3d printer)